2000 mercury 40 elpto manual. Reading : 2000 Mercury 40 Elpto Manual 2019-03-11

2000 mercury 40 elpto manual Rating: 9,4/10 1210 reviews

Outboard Motors

2000 mercury 40 elpto manual

Remove battery from its installation as soon as possible and remove all grease, sulfate and dirt from top surface by running water over top of bat- tery. Remove 4 bolts, washers, and isolators. Using a suitable punch, drive lower pivot pin into 6. Route key switch and trim switch harness d - Trim Switch through tiller bracket. We're selling purely due to recently becoming obsessed with kayak fishing ; Titles in-hand for both the boat and the trailer.

Next

Outboard Motors

2000 mercury 40 elpto manual

Secure impeller Quicksilver Anti-Corrosion Grease around the entire nut by bending tabs a against the flats on the im- mounting flange on the water intake housing and also to the threads on the six mounting bolts. The best products have the best dealers. Cam 2-4-C With Teflon 92-825407A12 51148 must open and close freely. This 59 cubic inch block provides superior performance and incredible hole-shots. Place one lead of Set ohmmeter to R x 1 scale. And don't forget the matching trailer - it's also fully loaded.

Next

Reading : 2000 Mercury 40 Elpto Manual

2000 mercury 40 elpto manual

Car- bon monoxide is the product of incomplete combus- Through the Environmental Protection Agency tion and is a dangerous, potentially lethal gas. With end of throttle cable connected to throttle le- Specifications ver, hold throttle lever against idle stop. Backed by decades of innovation and leadership, Mercury outboards are built to go the distance, delivering legendary performance driven by forward-thinking technology. Remove all burrs and filings from the memory piston. Open cam lever Down Position and screw cylinder cap down.

Next

Engine: 2000 Mercury 40 HP (40ELPTO)

2000 mercury 40 elpto manual

Install sacrificial aluminum anode to reservoir a - Trim Harness bracket placing ground strap between bracket and anode as shown. Install check valves and retainers into fuel pump Reassembly body. O-Ring Width Wiper Ring 412585 Cyl. Install components into propeller shaft in se- quence shown. Unscrew cylinder end cap assembly using span- accumulator. Prop Shaft, shift shaft, drive shaft, and water pump housing are all stainless steel for added strength and corrosion resistance. Install ball, seat, and spring five sets to shock ing Fluid.

Next

Reading : 2000 Mercury 40 Elpto Manual

2000 mercury 40 elpto manual

Slightest amount of debris in Power Trim system could cause system to malfunction. While holding flywheel with Flywheel Holder 1. Mercury outboard motor was made for the saltwater environment. Rotate drive shaft 5 to 10 revolutions. Pull up the cowl seal and remove the port side rubber grommet a. Power Trim System Removal 4.

Next

Outboard Motors

2000 mercury 40 elpto manual

The oil pump gear j rotation forces oil into the pas- sages for the up circuit. To prevent engine from start- ing while being cranked, all spark plugs must be removed. Hold throttle arm against full throttle stop. The internal shaft connected to the lever will open the down slow transfer valve i allowing oil under pressure into the cavity around the shaft. Slide shift actuator b toward the rear of engine reverse gear until resistance is felt. Place trim rod assembly on clean work surface.

Next

MERCURY 75 SERVICE MANUAL Pdf Download.

2000 mercury 40 elpto manual

Secure link rod between steering handle assem- bly and pilot rod end as shown. Use suitable punch to remove Drive Up lower Power Trim Disassembly pin. Divider Plate Insert remaining cover bolts - finger tighten. Above 5000 feet, however, it is recommended that main jet size be reduced as shown per 1000 feet 304. Eye protection must be worn while installing pis- ton pin lockrings.

Next

MERCURY 75 SERVICE MANUAL Pdf Download.

2000 mercury 40 elpto manual

Position shift lever handle into neutral detent. To raise the en- gine, the camshaft lever f is rotated all the way down. Install compression gauge in spark plug hole. Set ohmmeter to R x 1 scale. Insert propeller shaft assembly into bearing carrier. Check preload on throttle cable by placing a thin Throttle Cable Installation piece of paper between idle stop screw and idle and Adjustment to Engine stop.

Next

Mercury 50 ELPTO Service Manual

2000 mercury 40 elpto manual

If reverse gear must be replaced, pinion gear and sliding clutch should be inspected for damage. Replace shift cam if worn. Remove shock absorber from lower mount The shock absorber is pressurized with gas. This manual has everything you need to do repairs, service, and maintenance. Secure power trim assembly in soft jawed vise. Open manual release valve three turns maxi- mum counterclockwise and position trim rod to full up position.

Next