Am335x technical reference manual. AM335x Hardware Design Guide 2019-01-26

Am335x technical reference manual Rating: 8,3/10 1571 reviews

AM335x Hardware Design Guide

am335x technical reference manual

Configuring the functionality of a given multi-function pin, or pin multiplexing PinMux , is an important part of the embedded design process. The following example device tree block diagram shows the organization of the structure. Texas Instruments recommends that these devices not be used in any production system because their expected end-use failure rate still is undefined. Peripheral Information and Timings Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. In order to correctly configure the pin multiplexing, the pinctrl-single,pins entry of the device tree really just needs a list of numbers pairs:. Check the Basics This seems silly, but taking a step back from the specific problem you are facing can be very beneficial. Description The Starter Kit can be used as an evaluation and development platform for low cost based solutions and networking platforms.

Next

AM335x recovery

am335x technical reference manual

The more information you can provide, them the faster they will be able to provide useful feedback to help you solve your integration challenges. Once the unnecessary operation of software is eliminated, it becomes much easier to see where the problem is occuring. The guide follows the structure shown in the Hardware Design Timeline above. Peripheral Information and Timings Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. WiLink, Sitara , SmartConfig are trademarks of Texas Instruments. The tool includes the ability for the user to choose multiple application scenarios and understand the power consumption as well as how advanced power saving techniques can be applied to further reduce overall power consumption.

Next

User guides for AM335x, Unknown, Staging

am335x technical reference manual

Divide and Conquer Once the scope of the probem has been narrowed, its important to identify all the various hardware blocks that remain. If there are ever any discrepancies, the data-sheet and reference manuals should be considered the official source. Copies of these documents can be obtained directly from the internet or from your Texas Instruments representative. The guide follows the structure shown in the Software Design Timeline below. Narrowing the scope of the problem is typically done by removing as many variables from your software application while still being able to reproduce the problem. This can be especially helpful if you are using package dependencies such a drivers that were not developed by you. Remember, someone who has written the code is an expert at the code, and has likely come across and successfully debugged many of the issues you are currently seeing.

Next

AM335x recovery

am335x technical reference manual

Specifications Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. All prices include duty and customs fees on select shipping methods. As n side note, the address offset required for the pinctrl-single,pins entry is the Control Module register address offset minus 0x800. Constructing the Block Diagram The first step in designing the hardware platform is to create a detailed block diagram. See the below information on designing the clocking subsystem for your design. All other trademarks are the property of their respective owners. This functional pin map will allow you to configure pins appropriately in the device tree.

Next

User guides for AM335x, Unknown, Staging

am335x technical reference manual

Power and Clocking Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. Differential impedance should be Z x 2, where Z is the single- ended impedance defined in Table 7-60. Using this Guide, hardware designers can efficiently locate the resources they need at every step in the board design flow. For more information related to net classes, see Section 7. In reply to : Brandon, Thanks for quickly responding to Jaden on this. Note that the above restrictions only apply to booting from each port. A data bus width of x8 or x16 is supported.

Next

FAQ Management System

am335x technical reference manual

Peripheral Information and Timings Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. Specifications Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. When this is done, the signal routes on layer 4 should not cross splits in the power plane. Introduction The purpose of this software design guide is to walk developers through the various stages of designing software for this set of devices. For an overview of your device specific power structure, refer to your Sitara, C6-Integra, and DaVinci device Specific Technical Reference Manual Is this issue always reproducible? However, given there is no pin multiplexing defined, the designer first must declare the pins that should be used with the peripheral.

Next

TEXAS INSTRUMENTS AM335X SITARA MANUAL Pdf Download.

am335x technical reference manual

We also might not want to listen on all interfaces not to interfer with the rest of the system. Figure 1-Pin Mux Block Diagram The possible functions of each pin can be found in the. Product Integration Once the software is developed and debugged, the final step in the software development process is to take the code you've developed and port it to the actual hardware that will be integrated into your project. Creating the Schematics At this point in the design, it is time to start capturing the schematics. Sending simple oscilloscope captures is the most useful way to see how your system is specifically behaving is some of the best insight you can produce.

Next

FAQ Management System

am335x technical reference manual

Keep in mind that some boot sources take some time to timeout if that boot source isn't available. Terminal Configuration and Functions Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. The decoupling capacitor value depends on the board characteristics. While this approach does work, it quickly becomes a heavy burden on the developer to appropriate structure code to manage all events, when the code will need to manage for future undefined programs. Peripheral Information and Timings Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. Content on this site may contain or be subject to specific guidelines or limitations on use. Mouser® and Mouser Electronics® are trademarks of Mouser Electronics, Inc.

Next

Sitara AM335x datasheet & applicatoin notes

am335x technical reference manual

This can be easily prevented with the proper software configuration. When this is done, the signal routes on layer 4 should not cross splits in the power plane. Peripheral Information and Timings Copyright © 2011—2015, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links:. Development with no operating systems are typically discouraged as processors become more powerful and typically involve more lines of code because it requires an application to rely solely on interrupts for scheduling. The figures in the following subsections define the terms for the routing specification detailed in Table 7-66. This external memory buffer captures device-level information that allows obtaining accurate bus performance activity and throughput. Now we will create the dnsmasq.

Next