Electric component parts built in the microcomputer or relay are sensitive to heat and can easily get damaged. Always use high-grade fuels and lubricants, which correspond to the specifications in the specifications chapter of this manual. Connect the stroboscopic lamp and start the engine. Do not drop relays, sensors, or other electric components and do not expose them to vibration. Measure the lateral runout with the aid of two dial gauges. Standard value: 15 mm Measure the height of the roller weight.
Loosen the impeller screws and remove the impeller. In case of any defects in this part, the float shall be replaced. The lever must have a free travel α of 5-8°. The cover must first be removed from there in order to make it visible. Special tool: 000W-10 Put together bowth crankcase halves with the crankshaft. Use Loctite® 518 sealing compound only! Loosen the securing nut of the centrifugal clutch and remove the entire clutch together with the V-belt. Use battery chargers that are suited for those battery types e.
Remove the spark plug connector. Any ageing cracks in the intake manifold can be very harmful to the engine as foreign air can be suctioned and will cause leaning. Remove the fuel line, the carburetor heating and the oil hose from the carburetor. Measure the diameter of the guide sleeve. At the same time, the company produces a rather large range of its own vehicles.
Put out the cold start valve. Frame 1461986, engine 353 Feky 120028-6. Remove the carburetor and the air filter body. Check the intake manifold for crackings and fissures. A new product of the production program was a light motorcycle with a 50-cc two-stroke engine in two versions: dual-use Supercross and urban enduro Supermoto.
The actual value is the half of the measured value. Register a Free 1 month Trial Account. Loosen the securing bolts of the stator assembly and remove the stator. The carburetor can only properly adjusted and faults in the carburetor system can be detected when there are no mechanical defects in the engine or defectas in the fuel supply or in the ignition system. Check the individual clutch shoes for free movement. Heated up the right crankcase to approx.
If snap-in connections have latching clips, those connections can be interrupted by pressing the clips down according to the directions specified in the adjacent drawing. The latching clips are properly locked in place when you can hear a click noise. The problem is that once you have gotten your nifty new product, the manual for aragon cpi 2015 gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. The crankcase shall be heated up to approx. Remove the fan cover, the impeller, and the generator. If the arrow is no longer detectable, then the piston ring gaps must always be opposite to the opening.
Upper side wear limit: 16. After removing the supply line from the oil reservoir and the delivery line, which leads to the carburetor, both lines must be plugged with suitable plugs so that no oil can flow out. Immobilize the flywheel with a suitable tool and loosen the lock nut with a socket wrench. Prior to maintaining the electrical system, the ignition has to be switched off and the battery ground cable has to be disconnected. Fill the opening of the engine with a rag in order to avoid dirt or foreign material from entering the crankcase. Grease all movable parts upon the reassembly of the clutch in order to ensure the free movement of the clutch component parts. Hook in the control cable and adjust the cable play.
. Replace damaged or excessively worn roller weights. Pay attention not to chock the shaft seal. Many proceedings, techniques, tooling and components are known for the various maintenance works that are required for a vehicle, and the knowledge of motor vehicle technicians differs likewise. Remove the throttle control cable. If for maintenace works the temperature must be risen above 80 °C, those electric component parts have to be removed prior to maintenance. Measure the width of the V-belt upper and lower side.
To avoid slack, wiring harnesses have to be fixed with cable clamps or cable fastening ribbons. Before maintaining the carburetor, the engine, the fuel supply, and the ignition system have to be in a faultless state. Use a new sealing ring prior to mounting the float chamber cover. The allowable adjustment track to the full throttle position must be at least 70°. I am struggling to find any information on this bike online but am very interested in finding out more about the history of this bike.